Description
For large-area glass crystal bonding, use the K-303 50ml Transparent UV glue curing adhesive with a 9/51LED UV torch. like glass crafts, glass mosaics, and crystal crafts.
K-303 is devoted to the high adhesive strength of acrylic (PMMA) or acrylic adhesive between glass and metal. such as billboards made of acrylic. acrylic adhesive goods. but also for adhesive-fixing plastics and other transparent plastics including PC, PVC, PS, and ABS. connecting with outstanding outcomes. like plastic things, like bonding, and plastic packaging.
Qualities:
The information above is based on our comprehensive experiment, and the findings are trustworthy.
However, we have little control over the conditions because of the variety of actual use. Therefore, in order to ensure that the product is appropriate, consumers must be evaluated before use.
Under some circumstances, my company does not guarantee that the product will work properly. and disclaims all responsibility for incidental, direct, or indirect damages.
Users can get in touch with our technical assistance department if they run across any issues while using the system. We will do all in our power to assist you.
Follow these steps:
based on the surface treatment of the material. surface that is clean and dry. absence of a weak boundary layer;
Material for interface adhesive bonding where continuous coating is required. Take care not to scatter;
The glue is positioned in the brief UV curing lamp radiation using three lights. till the nudging hand was corrected;
Using a knife, scrape off any extra glue that overflows. or a cosy cloth. You can alternatively dip a paper towel in acetone and gently wipe away any extra adhesive. wipe with alcohol;
High radiation during the entire cure duration. until it is completely healed. observe that the temperature is not very high;
soaked in acetone. alcohol. Cleaning supplies: Use a paper towel or soft cloth to gently wipe the bonding material.
Usage guidelines:
The adhesive surface is dry, clean, and grease-free. Acetone can be used for wiping. dryer for hair.
The curing UV lamp was positioned. The glue's ability to absorb light energy from the light source connected to the light transmittance material and other variables determines the curing rate.
The procedure must not be squeezed too firmly to become sticky, nor should it be continually separated from the adherend.
To prevent contamination, do not return the remaining glue to the original packing.
Take note:
Don't let kids come into contact.
Steer clear of skin, clothing, and eyes. A small itch on the skin and these eyes.
After skin contact, immediately rinse with soap and water. Before they can wear the clothes, please wash them.
should it inadvertently splash into the eyes. Rinse with lots of water right away. since a trip to the hospital is not necessary.
Since UV Glue is a unique product, it can only be supplied via post mail. Shipping services are not available for this product in certain nations and areas.
Storage: This item is heat and light sensitive. You must store it somewhere dry and cool. out of direct sunlight below 28 °C. good for a year.
Important performance metrics:
Looks like a clear, pale liquid
Viscosity cps: 550 ± 100 (SC 4-15 rotor, Brookfield DV-II viscometer, 25 °C)
Shore D hardness (GB/T 531-1999 curing test): 53
K-303 will typically heal when exposed to ultraviolet light. Slowly, the sun will solidify. A light source at 220-260 nm aids in surface curing.
depth and cure rate. and a UV light source and dryness are the final curing effects. duration of exposure. materials related to light transmittance. experimentally recommended to ascertain the ultimate cure procedure.
6 seconds for a 125W Philips high-pressure fluorescent light to be positioned. UVA 3mm thick PMMA / PMMA; 4.5 mW / cm 2.
Typical cured qualities include an overlapping area of 25 × 5 = 125 mm2 and tensile shear strength (GB 7124-86). Both PS 30 ° C are destroyed by PS / PS 4-5MPa.